Get Juniper JN0-636 Dumps Questions [2024] To Gain Brilliant Result
JN0-636 dumps - TorrentValid - 100% Passing Guarantee
The JN0-636 certification exam covers a range of topics related to network security, including security policies and enforcement, security zones, virtual private networks (VPNs), intrusion detection and prevention, and security incidents and events. Candidates must demonstrate a deep understanding of Juniper Networks security solutions, including Junos Security, SRX Series Services Gateways, and Juniper Networks Advanced Threat Prevention (ATP). JN0-636 exam also tests candidates' ability to configure and manage Juniper Networks security solutions, including implementing security policies, configuring VPNs, and troubleshooting security issues.
NEW QUESTION # 53
Click the Exhibit button.
Which type of NAT is shown in the exhibit?
- A. persistent NAT
- B. NAT64
- C. DS-Lite
- D. NAT46
Answer: B
NEW QUESTION # 54
You are validating bidirectional traffic flows through your IPsec tunnel. The 4546 session represents traffic being sourced from the remote end of the IPsec tunnel. The 4547 session represents traffic that is sourced from the local network destined to the remote network.
Which statement is correct regarding the output shown in the exhibit?
- A. The local gateway address for the IPsec tunnel is 10.20.20.2
- B. NAT is being used to change the source address of outgoing packets
- C. The session information indicates that the IPsec tunnel has not been established
- D. The remote gateway address for the IPsec tunnel is 10.20.20.2
Answer: D
NEW QUESTION # 55
Which two modes are supported on Juniper ATP Cloud? (Choose two.)
- A. private mode
- B. Layer 3 mode
- C. global mode
- D. transparent mode
Answer: B,D
NEW QUESTION # 56
Click the Exhibit button.
userehost# run show route
inet.0: 4 destinations, 4 routes (4 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
0.0.0.0/0 *[Static/5] 00:05:06
> to 172.16.1.1 via ge-0/0/1.0
172.16.1.0/24 *[Direct/O] 00:05:06
> via ge-0/0/1.0
172.16.1.3/32 *[Local/0] 00:05:07
Local via ge-0/0/1.0
192.168.200.2/32 *[Local/0] 00:05:07
Reject
vr-a.inet.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)
+ = Active Route, - =
Last Active, * = Both
192.168.1.0/24 *[Direct/0] 00:01:05
> via ge-0/0/2.0
192.168.1.1/32 *[Local/0] 00:01:05
Local via ge-0/0/2.0
vr-b.inet.0: 2 destinations, 2 routes (2 active, 0 holddcwn, 0 hidden)
+ = Active Route, - =
Last Active, * = Both
192.168.1.0/24 *[Direct/O] 00:01:05
> via go-0/0/3.0
192.168.1.1/32 *[Local/0] 00:01:05
Local via ge-0/0/3.0
User 1 will access Server 1 using IP address 10.2.1.1.
You need to ensure that return traffic is able to reach User 1 from Server 1.
Referring to the exhibit, which two configurations allow this communication (Choose two.)
[edit security nat static]
- A. user@host# show
rule-set server-nat {
from zone [ junos-host untrust ];
rule 1 {
match {
destination-address 10.2.1.1/32;
}
then {
static-nat {
prefix {
192.168.1.2/32;
routing-instance vr-b;
}
}
}
}
}
[edit security nat static] - B. user@host# show
rule-set server-nat {
from zone untrust;
rule 1 {
match {
destination-address 10.2.1.1/32;
}
then {
static-nat {
prefix {
192.168.1.2/32;
routing-instance vr-a;
}
}
}
}
}
[edit security nat static] - C. user@host# show
rule-set in {
from zone untrust;
to zone cust-a;
rule overload {
match {
source-address 0.0.0.0/0;
}
then {
source-nat {
interface;
}
}
}
} - D. user@host# show
rule-set server-nat {
from zone [ untrust ];
rule 1 {
match {
destination-address 10.2.1.1/32;
}
then {
static-nat {
prefix {
192.168.1.2/32;
}
}
}
}
}
[edit security nat static]
Answer: A,B
NEW QUESTION # 57
Exhibit
You are implementing filter-based forwarding to send traffic from the 172.25.0.0/24 network through ISP-1 while sending all other traffic through your connection to ISP-2. Your ge-0/0/1 interface connects to two networks, including the 172.25.0.0/24 network. You have implemented the configuration shown in the exhibit. The traffic from the 172.25.0.0/24 network is being forwarded as expected to 172.20.0.2, however traffic from the other network (172.25.1.0/24) is not being forwarded to the upstream 172.21.0.2 neighbor.
In this scenario, which action will solve this problem?
- A. You must create the static default route to neighbor 172.21 0.2 under the ISP-1 routing instance hierarchy.
- B. You must add another term to the firewall filter to accept the traffic from the 172.25.1.0/24 network.
- C. You must specify that the 172.25.1.1/24 IP address is the primary address on the ge-0/0/1 interface.
- D. You must apply the firewall filter to the lo0 interface when using filter-based forwarding.
Answer: A
NEW QUESTION # 58
Referring to the exhibit, which three statements are true? (Choose three.)
- A. The packet originated within the Trust zone.
- B. The packet's destination is to a server in the DMZ zone.
- C. The packet's destination is to an interface on the SRX Series device.
- D. The packet is dropped before making an SSH connection.
- E. The packet is allowed to make an SSH connection.
Answer: A,C,D
NEW QUESTION # 59
Exhibit
You are using ATP Cloud and notice that there is a host with a high number of ETI and C&C hits sourced from the same investigation and notice that some of the events have not been automatically mitigated.
Referring to the exhibit, what is a reason for this behavior?
- A. The infected host score is globally set above a threat level of 5.
- B. The C&C events are false positives.
- C. The ETI events are false positives.
- D. The infected host score is globally set bellow a threat level of 5.
Answer: C
NEW QUESTION # 60
Click the Exhibit button.
user@key-server> show security group-vpn server ike security-
associations Index State Initiator cookie Responder cookie Mode Remote
Address
97 UP bb224408940cc5d 435b9404284083c2 Main 192.168.11.1
98 UP 242c840089404d15 ab19284089408ba8 Main 192.168.11.2
user@key-server> show security group-vpn server ipsec security-
associations Group:
group-1, Group Id: 1
Total IPsec SAs: 1
IPsec SA Algorithm SPI Lifetime
group-l-sa ESP:3des/shal 1343991c 2736
Group: group-2, Group id: 2
Total IPsec SAs: 1
IPsec SA Algorithm SPI Lifetime
group-2-sa ESP:3des/shal 13be9e9 2741
Group: group-3, Group Id: 3
Total IPsec SAs: 1
IPsec SA Algorithm SPI Lifetime
group-3-sa ESP:3des/shal 20709057 2741
Group: group-4, Group Id: 4
Total IPsec SAs: 1
IPsec SA Algorithm SPI Lifetime
group-4-sa ESP:3des/shal 5111c2e1 2741
Which statement is correct regarding the outputs shown in the exhibit?
- A. Four established peers are in the group VPNs.
- B. One established peer is in the group VPNs.
- C. No established peer is in the group VPNs.
- D. Two established peers are in the group VPNs.
Answer: D
NEW QUESTION # 61
Exhibit
You are validating bidirectional traffic flows through your IPsec tunnel. The 4546 session represents traffic being sourced from the remote end of the IPsec tunnel. The 4547 session represents traffic that is sourced from the local network destined to the remote network.
Which statement is correct regarding the output shown in the exhibit?
- A. The local gateway address for the IPsec tunnel is 10.20.20.2
- B. NAT is being used to change the source address of outgoing packets
- C. The session information indicates that the IPsec tunnel has not been established
- D. The remote gateway address for the IPsec tunnel is 10.20.20.2
Answer: D
NEW QUESTION # 62
Click the Exhibit button.
The IKE policy and proposal are configured properly on both devices as shown in the exhibit.
Which configuration snippet will complete the IKE configuration on the branch SRX Series device?
- A.
- B.
- C.
- D.
Answer: D
NEW QUESTION # 63
Exhibit
You are using traceoptions to verify NAT session information on your SRX Series device. Referring to the exhibit, which two statements are correct? (Choose two.)
- A. The SRX Series device is performing only source NAT on this session.
- B. The SRX Series device is performing both source and destination NAT on this session.
- C. This is the last packet in the session.
- D. This is the first packet in the session.
Answer: B,C
NEW QUESTION # 64
You are asked to implement the session cache feature on an SRX5400.
In this scenario, what information does a session cache entry record? (Choose two.)
- A. To which NPU the traffic of the session should be forwarded
- B. The type of processing to do for ingress traffic
- C. The type of processing to do for egress traffic
- D. To which SPU the traffic of the session should be forwarded
Answer: C,D
Explanation:
https://www.juniper.net/documentation/en_US/junos/topics/topic-map/security-packet-based- forwarding.html
NEW QUESTION # 65
Your company recently acquired a competitor. You want to use using the same IPv4 address space as your company.
Referring to the exhibit, which two actions solve this problem? (Choose two)
- A. Configure IPsec Transport mode.
- B. Identify two neutral IPv4 address spaces for address translation.
- C. Configure static NAT on the SRX Series devices.
- D. Connect the competitor network using IPsec policy-based VPNs.
Answer: C,D
NEW QUESTION # 66
What are two valid modes for the Juniper ATP Appliance? (Choose two.)
- A. core
- B. event collector
- C. all-in-one
- D. flow collector
Answer: C,D
NEW QUESTION # 67
You are asked to implement a Dynamic IPsec VPN on your new SRX240. You are required to facilitate up to 5 simultaneous users.
Which two statements must be considered when accomplishing the task?
- A. You must be a policy-based VPN.
- B. Your devices must be in a chassis cluster.
- C. You must use main mode for your IKE phase 1 policy.
- D. You must acquire at least three additional licenses.
Answer: A,D
NEW QUESTION # 68
While troubleshooting security policies, you added the count action. Where do you see the result of this action?
- A. In the show security flow statistics command output.
- B. In the show firewall log command output.
- C. In the show security policies hit-count command output.
- D. In the show security policies detail command output.
Answer: B
NEW QUESTION # 69
Which two statements are correct about the output shown in the exhibit? (Choose two.)
- A. The packet matches the default security policy.
- B. The packet is processed in the first path packet flow.
- C. The packet matches a configured security policy.
- D. The packet is processed as host inbound traffic.
Answer: A,D
NEW QUESTION # 70
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The configured solution allows IPv6 to IPv4 translation.
- B. External hosts cannot initiate contact.
- C. The IPv6 address is invalid.
- D. The configured solution allows IPv4 to IPv6 translation.
Answer: A,C
NEW QUESTION # 71
Referring to the exhibit. You configure a traceoptions file called radius on your returns the output shown in the exhibit. What is the source of the problem?
- A. The authentication order is misconfigured.
- B. The RADIUS server IP address is unreachable.
- C. The RADIUS server suffered a hardware failure.
- D. An incorrect password is being used.
Answer: C
NEW QUESTION # 72
Exhibit
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The data that traverses the ge-0/070 interface is secured by a secure association key.
- B. The data that traverses the ge-070/0 interface cannot be intercepted and read by anyone.
- C. The data that traverses the ge-070/0 interface can be intercepted and read by anyone.
- D. The data that traverses the ge-O/0/0 interface is secured by a connectivity association key.
Answer: B,C
NEW QUESTION # 73
What is a secure key management protocol used by IPsec?
- A. IKE
- B. ESP
- C. AH
- D. TCP
Answer: A
NEW QUESTION # 74
You are connecting two remote sites to your corporate headquarters site; you must ensure that all traffic is secured and only uses a single Phase 2 SA for both sites.
In this scenario, which VPN should be used?
- A. Full mesh IPsec VPNs with tunnels between all sites.
- B. A full mesh Layer 3 VPN with the corporate firewall acting as the hub device.
- C. A hub-and-spoke IPsec VPN with the corporate firewall acting as the hub device.
- D. An IPsec group VPN with the corporate firewall acting as the hub device.
Answer: D
NEW QUESTION # 75
......
To pass the JN0-636 exam, candidates are required to demonstrate their ability to identify and troubleshoot complex security issues, as well as design and configure advanced security solutions. JN0-636 exam covers a wide range of topics, including security policies, security zones, NAT, VPNs, and unified threat management (UTM). Candidates are also required to demonstrate their knowledge of advanced security technologies, such as intrusion prevention systems (IPS), application security, and advanced threat prevention.
The JN0-636 exam consists of 65 multiple-choice questions that need to be answered in 120 minutes. JN0-636 exam can be taken at any Pearson VUE testing center worldwide. Juniper Networks recommends that candidates have at least three to five years of experience in network security before taking JN0-636 exam.
Get 100% Passing Success With True JN0-636 Exam: https://freedumps.torrentvalid.com/JN0-636-valid-braindumps-torrent.html